|
sketchbook
|
All Classes Namespaces Files Functions Variables Typedefs Enumerations Enumerator Macros Groups Pages
|
sketchbook
|
( osboxes:~/sketchbook/cli/owslave$ sudo apt-get install gcc-avr_4.5.3 )
— using ATtiny84 (attiny84) —
-— programmer -—
Use Arduino Uno and my "Programmer Shield".
Open Arduino IDE (e.g. 1.6.5) and open File > Examples > ArdinoISP
Upload the sketch to an Arduino Uno board.
Adopt "Programmer Shield" to be wired for a tiny84, see sketch and: http://ww1.microchip.com/downloads/en/DeviceDoc/8006S.pdf http://www.3bm.de/2013/09/17/attiny84-mit-arduino-uno-programmieren/
-— chip -—
create or add you project.cfg (project.cfg.tiny84) to the folder
osboxes:~/sketchbook/cli/owslave$ nano Makefile
change the line -c -p -C +$$TF\ into -c -p t84 -b 19200 -P /dev/ttyACM0 -C +$$TF\ save and quit
osboxes:~/sketchbook/cli/owslave$ chmod +x cfg Cfg.py cfg_write gen_eeprom ordered_yaml.py
osboxes:~/sketchbook/cli/owslave$ make CFG=project.cfg try1 make[1]: Entering directory `/home/osboxes/sketchbook/cli/owslave' mkdir -p device/try1 MCU:atmega88 MCU_PROG:m88 PROG:avrisp AVRDUDE:sudo avrdude CFILES:moat_backend.c main.c jmp.S dev_data.c config.o timer.c ds2423.c onewire.c crc.c TYPE:alert -1 count 0 config -1 port 0 humid 0 pid 0 temp 0 console 0 smoke 0 pwm 0 adc 0 mkdir -p device/try1 ./cfg project.cfg .hdr try1 avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/moat_backend.o moat_backend.c avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/main.o main.c main.c:120:17: warning: ‘bootseq’ defined but not used [-Wunused-variable] static uint16_t bootseq attribute((section(".noinit"))); ^ avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/jmp.o jmp.S avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/dev_data.o dev_data.c set -e; \ ./gen_eeprom device/try1/eprom.bin type $(./cfg project.cfg .type try1); \ if ./gen_eeprom device/try1/eprom.bin name >/dev/null 2>&1 ; then : ; else \ ./gen_eeprom device/try1/eprom.bin name try1 ; fi ; \ if [ ds2423 != 0 ] ; then \ if ./gen_eeprom device/try1/eprom.bin owid serial >/dev/null 2>&1 ; then \ SER=$(./gen_eeprom device/try1/eprom.bin owid serial); \ if ./cfg project.cfg devices.try1.onewire_id >/dev/null 2>&1 ; then \ test "$(./cfg project.cfg devices.try1.onewire_id)" = "$SER" ; \ else \ ./cfg_write project.cfg devices.try1.onewire_id x$SER; \ fi; \ elif ./cfg project.cfg .nofollow devices.try1.onewire_id >/dev/null 2>&1 ; then \ SER=$(./cfg project.cfg devices.try1.onewire_id); \ ./gen_eeprom device/try1/eprom.bin owid type 0x$(./cfg project.cfg codes.onewire.ds2423) serial $SER; \ else \ ./gen_eeprom device/try1/eprom.bin owid type 0x$(./cfg project.cfg codes.onewire.ds2423) serial random; \ ./cfg_write project.cfg devices.try1.onewire_id x$(./gen_eeprom device/try1/eprom.bin owid serial); \ fi; \ fi avr-objcopy -I binary -O elf32-avr –prefix-sections=.eeprom \ –redefine-sym "_binary_device_try1_eprom_bin_start=_econfig_start" \ –redefine-sym "_binary_device_try1_eprom_bin_size=_econfig_size" \ –redefine-sym "_binary_device_try1_eprom_bin_end=_econfig_end" \ device/try1/eprom.bin device/try1/config.o avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/timer.o timer.c avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/ds2423.o ds2423.c avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/onewire.o onewire.c onewire.c:553:2: warning: #warning "Ignore the 'appears to be a misspelled signal handler' warning" [-Wcpp] #warning "Ignore the 'appears to be a misspelled signal handler' warning" ^ onewire.c: In function ‘real_PIN_INT’: onewire.c:554:6: warning: ‘real_PIN_INT’ appears to be a misspelled signal handler [enabled by default] void real_PIN_INT(void) { ^ avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/crc.o crc.c avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -o device/try1/image.elf -Wl,-Map,device/try1/image.map,–cref device/try1/moat_backend.o device/try1/main.o device/try1/jmp.o device/try1/dev_data.o device/try1/config.o device/try1/timer.o device/try1/ds2423.o device/try1/onewire.o device/try1/crc.o avr-objcopy -R .eeprom -O ihex device/try1/image.elf device/try1/image.hex avr-objcopy -j .eeprom –change-section-address .eeprom=0 -O ihex device/try1/image.elf device/try1/eprom.hex avr-objdump -h -S device/try1/image.elf > device/try1/image.lss make[1]: Leaving directory `/home/osboxes/sketchbook/cli/owslave'
Press RESET button on "Programmer Shield".
Insert tiny84 into "Programmer Shield" socket (connect ISP).
Press RESET button on "Programmer Shield". LED (Pin 8) should be off.
osboxes:~/sketchbook/cli/owslave$ make CFG=project.cfg burn_try1 BURN try1 make[1]: Entering directory `/home/osboxes/sketchbook/cli/owslave' LFUSE:E2 HFUSE:DC EFUSE:00 EEPROM:1 MCU:atmega88 MCU_PROG:m88 PROG:avrisp AVRDUDE:sudo avrdude CFILES:moat_backend.c main.c jmp.S dev_data.c config.o timer.c ds2423.c onewire.c crc.c TYPE:alert -1 humid 0 temp 0 pid 0 smoke 0 adc 0 port 0 config -1 pwm 0 console 0 count 0 set -e; \ ./gen_eeprom device/try1/eprom.bin type $(./cfg project.cfg .type try1); \ if ./gen_eeprom device/try1/eprom.bin name >/dev/null 2>&1 ; then : ; else \ ./gen_eeprom device/try1/eprom.bin name try1 ; fi ; \ if [ ds2423 != 0 ] ; then \ if ./gen_eeprom device/try1/eprom.bin owid serial >/dev/null 2>&1 ; then \ SER=$(./gen_eeprom device/try1/eprom.bin owid serial); \ if ./cfg project.cfg devices.try1.onewire_id >/dev/null 2>&1 ; then \ test "$(./cfg project.cfg devices.try1.onewire_id)" = "$SER" ; \ else \ ./cfg_write project.cfg devices.try1.onewire_id x$SER; \ fi; \ elif ./cfg project.cfg .nofollow devices.try1.onewire_id >/dev/null 2>&1 ; then \ SER=$(./cfg project.cfg devices.try1.onewire_id); \ ./gen_eeprom device/try1/eprom.bin owid type 0x$(./cfg project.cfg codes.onewire.ds2423) serial $SER; \ else \ ./gen_eeprom device/try1/eprom.bin owid type 0x$(./cfg project.cfg codes.onewire.ds2423) serial random; \ ./cfg_write project.cfg devices.try1.onewire_id x$(./gen_eeprom device/try1/eprom.bin owid serial); \ fi; \ fi avr-objcopy -I binary -O elf32-avr –prefix-sections=.eeprom \ –redefine-sym "_binary_device_try1_eprom_bin_start=_econfig_start" \ –redefine-sym "_binary_device_try1_eprom_bin_size=_econfig_size" \ –redefine-sym "_binary_device_try1_eprom_bin_end=_econfig_end" \ device/try1/eprom.bin device/try1/config.o avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -o device/try1/image.elf -Wl,-Map,device/try1/image.map,–cref device/try1/moat_backend.o device/try1/main.o device/try1/jmp.o device/try1/dev_data.o device/try1/config.o device/try1/timer.o device/try1/ds2423.o device/try1/onewire.o device/try1/crc.o avr-objcopy -R .eeprom -O ihex device/try1/image.elf device/try1/image.hex avr-objcopy -j .eeprom –change-section-address .eeprom=0 -O ihex device/try1/image.elf device/try1/eprom.hex avr-objdump -h -S device/try1/image.elf > device/try1/image.lss TF=$(mktemp avrdude-cfg.XXXXX); echo "default_safemode = no;" >$TF; \ EFUSE=00; \ [ "" != "" ] && SET_EFUSE="-U efuse:w:0x00:m"; \ sudo avrdude -c avrisp -p t84 -b 19200 -P /dev/ttyACM0 -C +$TF\ -U flash:w:device/try1/image.hex:i -U eeprom:w:device/try1/eprom.hex:i \ -U lfuse:w:0xE2:m \ -U hfuse:w:0xDC:m \ \ ; X=$?; rm $TF; exit $X
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.05s
avrdude: Device signature = 0x1e930c avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed To disable this feature, specify the -D option. avrdude: erasing chip avrdude: reading input file "device/try1/image.hex" avrdude: writing flash (3338 bytes):
Writing | ################################################## | 100% 5.65s
avrdude: 3338 bytes of flash written avrdude: verifying flash memory against device/try1/image.hex: avrdude: load data flash data from input file device/try1/image.hex: avrdude: input file device/try1/image.hex contains 3338 bytes avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 3.90s
avrdude: verifying ... avrdude: 3338 bytes of flash verified avrdude: reading input file "device/try1/eprom.hex" avrdude: writing eeprom (26 bytes):
Writing | ################################################## | 100% 1.55s
avrdude: 26 bytes of eeprom written avrdude: verifying eeprom memory against device/try1/eprom.hex: avrdude: load data eeprom data from input file device/try1/eprom.hex: avrdude: input file device/try1/eprom.hex contains 26 bytes avrdude: reading on-chip eeprom data:
Reading | ################################################## | 100% 0.29s
avrdude: verifying ... avrdude: 26 bytes of eeprom verified avrdude: reading input file "0xE2" avrdude: writing lfuse (1 bytes):
Writing | ################################################## | 100% 0.02s
avrdude: 1 bytes of lfuse written avrdude: verifying lfuse memory against 0xE2: avrdude: load data lfuse data from input file 0xE2: avrdude: input file 0xE2 contains 1 bytes avrdude: reading on-chip lfuse data:
Reading | ################################################## | 100% 0.02s
avrdude: verifying ... avrdude: 1 bytes of lfuse verified avrdude: reading input file "0xDC" avrdude: writing hfuse (1 bytes):
Writing | ################################################## | 100% 0.02s
avrdude: 1 bytes of hfuse written avrdude: verifying hfuse memory against 0xDC: avrdude: load data hfuse data from input file 0xDC: avrdude: input file 0xDC contains 1 bytes avrdude: reading on-chip hfuse data:
Reading | ################################################## | 100% 0.02s
avrdude: verifying ... avrdude: 1 bytes of hfuse verified
avrdude done. Thank you.
make[1]: Leaving directory `/home/osboxes/sketchbook/cli/owslave' osboxes:~/sketchbook/cli/owslave$
BINGO! It works! :))
test now... (https://github.com/M-o-a-T/owslave/blob/master/HOWTO.md) onewire_io Choose which pin to connect your 1wire bus to. For now, only pins with dedicated interrupts (INTx) can be used. On an ATmega168, these are pins D2 and D3. The default is INT0. http://ww1.microchip.com/downloads/en/DeviceDoc/8006S.pdf INT0 -> Pin 5 PCINT0 -> Pin 13 VCC -> Pin 1 GND -> Pin 14
DOES NOT WORK ON THE BUS - MAY BE DUE TO THE FACT THAT 't84' IS NOT RECOGNIZED AND IT COMPILES AS 'm88'.
See also: https://electronics.stackexchange.com/questions/205055/using-avrdude-to-program-attiny-via-arduino-as-isp https://forum.arduino.cc/index.php?topic=349912.0
— Issues —
In project.cfg "defaults.target.t85" is recognized as attiny85 but does NOT compile.
In project.cfg "defaults.target.t84" is NOT recognized as attiny84 but does compile as m88 (atmega88).
— using ATmega88 (mega88) —
https://www.avrprogrammers.com/articles/atmega8-vs-atmega328
-— programmer -—
Use Arduino Uno and my "Programmer Shield".
Open Arduino IDE (e.g. 1.6.5) and open File > Examples > ArdinoISP
Upload the sketch to an Arduino Uno board.
Adopt "Programmer Shield" to be wired for a mega88, see sketch and: http://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-2545-8-bit-AVR-Microcontroller-ATmega48-88-168_Summary.pdf
-— chip -—
create or add you project.cfg (project.cfg.mega88) to the folder
osboxes:~/sketchbook/cli/owslave$ nano Makefile
change the line -c -p -C +$$TF\ into -c -p -b 19200 -P /dev/ttyACM0 -C +$$TF\ save and quit
( osboxes:~/sketchbook/cli/owslave$ chmod +x cfg Cfg.py cfg_write gen_eeprom ordered_yaml.py )
osboxes:~/sketchbook/cli/owslave$ make CFG=project.cfg try1 make[1]: Entering directory `/home/osboxes/sketchbook/cli/owslave' mkdir -p device/try1 MCU:atmega88 MCU_PROG:m88 PROG:avrisp AVRDUDE:sudo avrdude CFILES:moat_backend.c main.c jmp.S dev_data.c config.o timer.c ds2423.c onewire.c crc.c TYPE:port 0 temp 0 pwm 0 alert -1 adc 0 console 0 pid 0 config -1 humid 0 count 0 smoke 0 mkdir -p device/try1 ./cfg project.cfg .hdr try1 avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/moat_backend.o moat_backend.c avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/main.o main.c main.c:120:17: warning: ‘bootseq’ defined but not used [-Wunused-variable] static uint16_t bootseq attribute((section(".noinit"))); ^ avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/jmp.o jmp.S avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/dev_data.o dev_data.c set -e; \ ./gen_eeprom device/try1/eprom.bin type $(./cfg project.cfg .type try1); \ if ./gen_eeprom device/try1/eprom.bin name >/dev/null 2>&1 ; then : ; else \ ./gen_eeprom device/try1/eprom.bin name try1 ; fi ; \ if [ ds2423 != 0 ] ; then \ if ./gen_eeprom device/try1/eprom.bin owid serial >/dev/null 2>&1 ; then \ SER=$(./gen_eeprom device/try1/eprom.bin owid serial); \ if ./cfg project.cfg devices.try1.onewire_id >/dev/null 2>&1 ; then \ test "$(./cfg project.cfg devices.try1.onewire_id)" = "$SER" ; \ else \ ./cfg_write project.cfg devices.try1.onewire_id x$SER; \ fi; \ elif ./cfg project.cfg .nofollow devices.try1.onewire_id >/dev/null 2>&1 ; then \ SER=$(./cfg project.cfg devices.try1.onewire_id); \ ./gen_eeprom device/try1/eprom.bin owid type 0x$(./cfg project.cfg codes.onewire.ds2423) serial $SER; \ else \ ./gen_eeprom device/try1/eprom.bin owid type 0x$(./cfg project.cfg codes.onewire.ds2423) serial random; \ ./cfg_write project.cfg devices.try1.onewire_id x$(./gen_eeprom device/try1/eprom.bin owid serial); \ fi; \ fi avr-objcopy -I binary -O elf32-avr –prefix-sections=.eeprom \ –redefine-sym "_binary_device_try1_eprom_bin_start=_econfig_start" \ –redefine-sym "_binary_device_try1_eprom_bin_size=_econfig_size" \ –redefine-sym "_binary_device_try1_eprom_bin_end=_econfig_end" \ device/try1/eprom.bin device/try1/config.o avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/timer.o timer.c avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/ds2423.o ds2423.c avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/onewire.o onewire.c onewire.c:553:2: warning: #warning "Ignore the 'appears to be a misspelled signal handler' warning" [-Wcpp] #warning "Ignore the 'appears to be a misspelled signal handler' warning" ^ onewire.c: In function ‘real_PIN_INT’: onewire.c:554:6: warning: ‘real_PIN_INT’ appears to be a misspelled signal handler [enabled by default] void real_PIN_INT(void) { ^ avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -c -o device/try1/crc.o crc.c avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -o device/try1/image.elf -Wl,-Map,device/try1/image.map,–cref device/try1/moat_backend.o device/try1/main.o device/try1/jmp.o device/try1/dev_data.o device/try1/config.o device/try1/timer.o device/try1/ds2423.o device/try1/onewire.o device/try1/crc.o avr-objcopy -R .eeprom -O ihex device/try1/image.elf device/try1/image.hex avr-objcopy -j .eeprom –change-section-address .eeprom=0 -O ihex device/try1/image.elf device/try1/eprom.hex avr-objdump -h -S device/try1/image.elf > device/try1/image.lss make[1]: Leaving directory `/home/osboxes/sketchbook/cli/owslave'
Press RESET button on "Programmer Shield" if LED (Pin 8) is on (should be off).
osboxes:~/sketchbook/cli/owslave$ make CFG=project.cfg burn_try1 BURN try1 make[1]: Entering directory `/home/osboxes/sketchbook/cli/owslave' LFUSE:E2 HFUSE:DC EFUSE:00 EEPROM:1 MCU:atmega88 MCU_PROG:m88 PROG:avrisp AVRDUDE:sudo avrdude CFILES:moat_backend.c main.c jmp.S dev_data.c config.o timer.c ds2423.c onewire.c crc.c TYPE:smoke 0 humid 0 temp 0 pwm 0 adc 0 port 0 config -1 alert -1 console 0 count 0 pid 0 set -e; \ ./gen_eeprom device/try1/eprom.bin type $(./cfg project.cfg .type try1); \ if ./gen_eeprom device/try1/eprom.bin name >/dev/null 2>&1 ; then : ; else \ ./gen_eeprom device/try1/eprom.bin name try1 ; fi ; \ if [ ds2423 != 0 ] ; then \ if ./gen_eeprom device/try1/eprom.bin owid serial >/dev/null 2>&1 ; then \ SER=$(./gen_eeprom device/try1/eprom.bin owid serial); \ if ./cfg project.cfg devices.try1.onewire_id >/dev/null 2>&1 ; then \ test "$(./cfg project.cfg devices.try1.onewire_id)" = "$SER" ; \ else \ ./cfg_write project.cfg devices.try1.onewire_id x$SER; \ fi; \ elif ./cfg project.cfg .nofollow devices.try1.onewire_id >/dev/null 2>&1 ; then \ SER=$(./cfg project.cfg devices.try1.onewire_id); \ ./gen_eeprom device/try1/eprom.bin owid type 0x$(./cfg project.cfg codes.onewire.ds2423) serial $SER; \ else \ ./gen_eeprom device/try1/eprom.bin owid type 0x$(./cfg project.cfg codes.onewire.ds2423) serial random; \ ./cfg_write project.cfg devices.try1.onewire_id x$(./gen_eeprom device/try1/eprom.bin owid serial); \ fi; \ fi avr-objcopy -I binary -O elf32-avr –prefix-sections=.eeprom \ –redefine-sym "_binary_device_try1_eprom_bin_start=_econfig_start" \ –redefine-sym "_binary_device_try1_eprom_bin_size=_econfig_size" \ –redefine-sym "_binary_device_try1_eprom_bin_end=_econfig_end" \ device/try1/eprom.bin device/try1/config.o avr-gcc -g -mmcu=atmega88 -Wall -Wstrict-prototypes -Os -mcall-prologues -fshort-enums -Idevice/try1 -o device/try1/image.elf -Wl,-Map,device/try1/image.map,–cref device/try1/moat_backend.o device/try1/main.o device/try1/jmp.o device/try1/dev_data.o device/try1/config.o device/try1/timer.o device/try1/ds2423.o device/try1/onewire.o device/try1/crc.o avr-objcopy -R .eeprom -O ihex device/try1/image.elf device/try1/image.hex avr-objcopy -j .eeprom –change-section-address .eeprom=0 -O ihex device/try1/image.elf device/try1/eprom.hex avr-objdump -h -S device/try1/image.elf > device/try1/image.lss TF=$(mktemp avrdude-cfg.XXXXX); echo "default_safemode = no;" >$TF; \ EFUSE=00; \ [ "" != "" ] && SET_EFUSE="-U efuse:w:0x00:m"; \ sudo avrdude -c avrisp -p m88 -b 19200 -P /dev/ttyACM0 -C +$TF\ -U flash:w:device/try1/image.hex:i -U eeprom:w:device/try1/eprom.hex:i \ -U lfuse:w:0xE2:m \ -U hfuse:w:0xDC:m \ \ ; X=$?; rm $TF; exit $X [sudo] password for osboxes:
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.02s
avrdude: Device signature = 0x1e930a avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed To disable this feature, specify the -D option. avrdude: erasing chip avrdude: reading input file "device/try1/image.hex" avrdude: writing flash (3338 bytes):
Writing | ################################################## | 100% 4.99s
avrdude: 3338 bytes of flash written avrdude: verifying flash memory against device/try1/image.hex: avrdude: load data flash data from input file device/try1/image.hex: avrdude: input file device/try1/image.hex contains 3338 bytes avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 2.60s
avrdude: verifying ... avrdude: 3338 bytes of flash verified avrdude: reading input file "device/try1/eprom.hex" avrdude: writing eeprom (26 bytes):
Writing | ################################################## | 100% 1.37s
avrdude: 26 bytes of eeprom written avrdude: verifying eeprom memory against device/try1/eprom.hex: avrdude: load data eeprom data from input file device/try1/eprom.hex: avrdude: input file device/try1/eprom.hex contains 26 bytes avrdude: reading on-chip eeprom data:
Reading | ################################################## | 100% 0.11s
avrdude: verifying ... avrdude: 26 bytes of eeprom verified avrdude: reading input file "0xE2" avrdude: writing lfuse (1 bytes):
Writing | ################################################## | 100% 0.02s
avrdude: 1 bytes of lfuse written avrdude: verifying lfuse memory against 0xE2: avrdude: load data lfuse data from input file 0xE2: avrdude: input file 0xE2 contains 1 bytes avrdude: reading on-chip lfuse data:
Reading | ################################################## | 100% 0.01s
avrdude: verifying ... avrdude: 1 bytes of lfuse verified avrdude: reading input file "0xDC" avrdude: writing hfuse (1 bytes):
Writing | ################################################## | 100% 0.02s
avrdude: 1 bytes of hfuse written avrdude: verifying hfuse memory against 0xDC: avrdude: load data hfuse data from input file 0xDC: avrdude: input file 0xDC contains 1 bytes avrdude: reading on-chip hfuse data:
Reading | ################################################## | 100% 0.01s
avrdude: verifying ... avrdude: 1 bytes of hfuse verified
avrdude done. Thank you.
make[1]: Leaving directory `/home/osboxes/sketchbook/cli/owslave' osboxes:~/sketchbook/cli/owslave$
Test the device by connecting it to a 1-wire bus and check for the presence of a new DS2423.
(https://github.com/M-o-a-T/owslave/blob/master/HOWTO.md) onewire_io Choose which pin to connect your 1wire bus to. For now, only pins with dedicated interrupts (INTx) can be used. On an ATmega168, these are pins D2 and D3. The default is INT0.
BINGO! It works! :))
— using Tiny (not working yet) —
Issues with ATtiny85: https://github.com/M-o-a-T/owslave/issues/16 Support for ATtiny84: https://github.com/M-o-a-T/owslave/issues/17
— using Arduino Uno or Nano Board (not recommened) —
You need to bypass the bootloader and program the raw/whole chip by connecting another Arduino Board to the ISP header of the first (the one to be programmed). See https://www.arduino.cc/en/Tutorial/ArduinoISP
During this process the bootloader get bypassed and overwritten, so to use the Board as usual again you have to load the bootloader by ISP header again.
You should also check first whether the pins wirde on the Board are the ones you need and that they are wired properly.
The Makefile should then may be contain something like: -c arduino -p atmega328p -b 57600 -P /dev/ttyUSB0 -C +$$TF\
1.8.6